
This is now week 14 of our #SensorFAQs series which you can join in and follow on our twitter page.
We’ll be sharing Frequently Asked Questions we receive from our customers to help provide expert insights into our product range, the sensor industry and more.
This week we answer ‘What types of interface boards can I use with SST’s Zirconia O2 Sensors?’
Details for next weeks #SensorFAQs:
Date & Time: Tuesday, 13th August 2019, 1.00pm GMT
Channel: #SensorFAQs
#SensorFAQs – Q14 | What types of interface boards can I use With SST’s Zirconia O2 Sensors? pic.twitter.com/wIiPNdPsoe
— SST Sensing Ltd (@SSTSensingLtd) August 6, 2019
Answers
#SensorFAQs – Q14 1/8 | In order to operate any of SST’s Zirconia O2 Sensors, you will require an interface board which provides the electronics necessary to power and control the zirconium dioxide oxygen sensors. https://t.co/AbTycapKJC
— SST Sensing Ltd (@SSTSensingLtd) August 6, 2019
#SensorFAQs – Q14 2/8 | Alternatively, if you would rather have a complete solution, have a complete solution, the Zirconia Oxygen Measurement System or OXY-Flex may better suit your needs. When choosing the option you require, you should consider the following: https://t.co/AbTycapKJC
— SST Sensing Ltd (@SSTSensingLtd) August 6, 2019
#SensorFAQs – Q14 3/8 |
1. O₂ measurement range; 0.1-25% or 0.1-100%
2. Output requirements; digital (RS485 Modbus or RS232) or analogue (4-20mA or 0-10Vdc) https://t.co/AbTycapKJC— SST Sensing Ltd (@SSTSensingLtd) August 6, 2019
#SensorFAQs – Q14 4/8 |
3. Location; cable length is important; to maintain the correct sensor heater voltage and minimize noise pick up, SST recommends keeping the cable length between the sensor and interface board as short as possible. https://t.co/AbTycapKJC
— SST Sensing Ltd (@SSTSensingLtd) August 6, 2019
#SensorFAQs – Q14 5/8 |
4. Convenience; do you want an “off-the-shelf” solution or configure the equipment yourself? If you want to design the board yourself. Please refer to our Zirconia Sensor Software and Hardware Design Guide below:https://t.co/xtHOMnXoGh https://t.co/AbTycapKJC
— SST Sensing Ltd (@SSTSensingLtd) August 6, 2019
#SensorFAQs – Q14 6/8 | Types of Interface Boards
There a number of options available which enable you to power and control SST’s range of zirconium dioxide o2 sensors; interface board or a complete solution. The following gives a brief overview of each type of interface PCB. https://t.co/AbTycapKJC
— SST Sensing Ltd (@SSTSensingLtd) August 6, 2019
#SensorFAQs – Q14 7/8 | OXY-LC Interface
The OXY-LC Interface Board has a built-in pressure sensor for barometric pressure compensation.
Product specification can be found here: https://t.co/c9GGS8ZwWW https://t.co/AbTycapKJC
— SST Sensing Ltd (@SSTSensingLtd) August 6, 2019
#SensorFAQs – Q14 8/8 | O2I-Flex Interface
The O2I-FLEX has externally triggered automatic or manual calibration. Calibration can also be initiated via an on-board push button switch.
Product specification can be found here: https://t.co/HKWmFrsILy https://t.co/AbTycapKJC
— SST Sensing Ltd (@SSTSensingLtd) August 6, 2019
